<h1id="femtofox----subsubthe-tiny-low-power-linux-meshtastic-node">Femtofox <sub><sub>The tiny, low power Linux Meshtastic node</sub></sub></h1>
<h4id="the-luckfox-pico-mini-is-a-compact-and-power-efficient-linux-capable-board-capable-of-running-ubuntu.-femtofox-is-an-expansion-of-the-luckfoxs-capabilities-combining-a-customized-ubuntu-image-with-a-custom-pcb-integrating-it-with-a-lora-radio-to-create-a-power-efficient-cheap-and-small-meshtastic-linux-node.">The Luckfox Pico Mini is a compact and power efficient Linux capable board, capable of running Ubuntu. Femtofox is an expansion of the Luckfox’s capabilities, combining a customized Ubuntu image with a custom PCB, integrating it with a LoRa radio to create a power efficient, cheap and small Meshtastic Linux node.</h4>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Meshtastic native client controlling a LoRa radio (see <ahref="supported_hardware.md">supported hardware</a>)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> WIFI over USB (see <ahref="supported_hardware.md">supported hardware</a>)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Ethernet over USB (see <ahref="supported_hardware.md">supported hardware</a>)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Ethernet over pins (see <em>Networking</em> below and wiring diagram at bottom of page)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> UART communications with Meshtastic nodes (2 pin pairs) such as RAK Wisblock</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> USB serial communications with Meshtastic nodes (see <ahref="supported_hardware.md">supported hardware</a>)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Real time clock (RTC) support (see <ahref="supported_hardware.md">supported hardware</a>)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Activity LED disabled. User LED will blink for 5 seconds when boot is complete</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Pressing the “BOOT” button triggers reboot</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Ability to reconfigure wifi via USB flash drive</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Meshtasticd to run LoRa radio over SPI (accomplished, updated image and instructions coming soon)</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Allow editing of config files by plugging in thumb drive</li>
<liclass="task-list-item"><inputtype="checkbox"class="task-list-item-checkbox"checked="true"disabled=""> Ability to activate or deactivate WIFI via Meshtastic admin</li>
<p>The preconfigured images will reboot every 24 hours. If the internal clock is accurate, this will be at 3am. Reboot timing is set in <code>crontab</code>. To keep accurate time, an RTC module can be installed (see <ahref="supported_hardware.md">supported hardware</a>) or internet connectivity can be maintained for NTP. If no authoritative time source is found, time will be set to 2024-01-01 00:00 on boot.</p>
<li>RDNIS via usb - <ahref="https://web.archive.org/web/20241006173648/https://wiki.luckfox.com/Luckfox-Pico/Luckfox-Pico-Network-Sharing-1/">see this guide</a>. Note that in the preconfigured images USB is set to host mode, so you’ll have to switch back to peripheral with <code>sudo luckfox-config</code>. This is not really recommended, but can be used in a pinch.</li>
<li>Flash the image your MicroSD card using <ahref="https://etcher.balena.io/">Balena Etcher</a> or your favorite flashing program. You will likely get a warning that the image appears to be invalid or has no partition table. This is normal.</li>
Meshtastic® is a registered trademark of Meshtastic LLC. Meshtastic software components are released under various licenses, see GitHub for details. No warranty is provided - use at your own risk.</p>