<h3id="the-luckfox-pico-mini-is-a-compact-and-power-efficient-0.25w-linux-capable-board-ideal-for-running-tc2-meshtastic-bbs-or-anything-else.">The Luckfox Pico Mini is a compact and power efficient (~0.25w) Linux capable board, ideal for running <ahref="https://github.com/TheCommsChannel/TC2-BBS-mesh">TC2 Meshtastic BBS</a> (or anything else).</h3>
<li>Cheap - $7-8 on <ahref="https://www.waveshare.com/luckfox-pico-min.htm">Waveshare</a> (also available on Amazon)! Get the A model - the B just has added flash storage that’s too small for our purposes.</li>
<li>By default, no simple way to get online (no built in wifi/BLE/ethernet). Ethernet can be easily added - wifi still work in progress - see <em>Networking</em> below)</li>
<h3id="after-many-hours-of-fiddling-ive-cobbled-together-an-ubuntu-image-with-support-for">After many hours of fiddling, I’ve cobbled together an ubuntu image with support for:</h3>
<li>Drivers for real time clock over i2c - tested working with <ahref="https://aliexpress.com/item/1005007143842437.html">DS3231</a> with DS1307 driver (should be compatible with DS1307, DS1337 and DS3231).</li>
<li><ahref="https://drive.google.com/file/d/17ofd-bt6IVE3EDBe9cu1_IK2BuYEeg_a/view?usp=sharing">A ‘fresh’ image with no changes but with the added drivers for usb ethernet, wifi, serial, RTC and mass storage.</a></li>
<li><ahref="https://drive.google.com/file/d/1YSlR-At4rCv29A_f9hgME6Z_D2mZ1WO3/view?usp=drive_link">An image preconfigured with the TC2-BBS for comms over UART4.</a></li>
<li><ahref="https://drive.google.com/file/d/1iXApWAXAhl-iirATAJVD0Ilr2K8OdY3i/view?usp=sharing">An image preconfigured with the TC2-BBS for comms over USB.</a> This assumes the USB device is recognized as /dev/ttyACM0.</li>
<p>Login for the “fresh” image is <code>root:root</code> or <code>pico:luckfox</code>. Login for the configured BBS images is <code>bbs:mesh</code>.</p>
<p>The preconfigured images will reboot every 24 hours, and restart the BBS every other hour. In theory, this should happen at 7am UTC (because both the US and Europe are generally inactive at that time). Time is set on boot with the following logic:</p>
<ol>
<li>If the system recognizes an RTC module connected via i2c, it will use that.</li>
<li>If no RTC module is recognized, time will be set to midnight 24/1/1.</li>
<li>If network is available, time will be retrieved from google and system time (and RTC time if present) will be set from that.</li>
<li>RDNIS via usb - <ahref="https://web.archive.org/web/20241006173648/https://wiki.luckfox.com/Luckfox-Pico/Luckfox-Pico-Network-Sharing-1/">see this guide</a>. Note that in the preconfigured images USB is set to host mode, so you’ll have to switch back to peripheral with <code>sudo luckfox-config</code>.</li>
<li>Preconfigured ubuntu images: ethernet via the castellated pins at the bottom of the board. See pinout at the bottom of this readme. Note that the MAC address for onboard ethernet is 1a:cf:50:33:5f:92 - if you need to change this, <code>sudo nano /etc/network/interfaces</code>.</li>
<p><strong>Choosing a MicroSD card:</strong> Any reasonably fast MicroSD card of 32gb or higher should work, but ideally use a card that supports UHS-1 or higher, and is rated for high endurance.</p>
<li>Flash the image your MicroSD card using <ahref="https://etcher.balena.io/">Balena Etcher</a> or your favorite flashing program. You will likely get a warning that the image appears to be invalid or has no partition table. This is normal.</li>
<li>You can connect to the Luckfox via ethernet or UART serial as described <ahref="https://wiki.luckfox.com/Luckfox-Pico/Luckfox-Pico-RV1103/Luckfox-Pico-Login-UART/">here</a>.</li>