diff --git a/supported_hardware.md b/supported_hardware.md index 582eb38..36477f0 100644 --- a/supported_hardware.md +++ b/supported_hardware.md @@ -74,13 +74,6 @@ -rl8188cu - - - - - - rtl8187 @@ -363,9 +356,9 @@ ar9271 ✔️ -❌ +❔ -Buggy +Tested:
TP-Link TL-WR722N V1: working
Generic AR9271 w/SMA antenna: buggy
Work in progress ar9k diff --git a/usb_config.md b/usb_config.md index 54e2385..595515e 100644 --- a/usb_config.md +++ b/usb_config.md @@ -56,7 +56,7 @@ Options are:

[!CAUTION]
-Attempting to set wifi settings via USB configuration tool without a wifi adapter connected will lead to a hard crash - you will need to disconnect and reconnect power to recover.

+Attempting to set wifi settings via USB configuration tool without a wifi adapter connected will lead to a 5 minute hang while the configuration tool runs - either disconnect and reconnect power or wait the full 5 minutes to to recover.

To apply your configuration, reboot the Femtofox with the USB drive plugged in. No other USB drives can be plugged in at the same time.
A log (femtofox-config.log) is saved to /home/femto and the USB drive (except on NTFS, which is read only).
@@ -76,37 +76,37 @@ A log (femtofox-config.log) is saved to /home/femto an -⚠️ 1 very long blink, lasting 4 seconds
_____________ +

⚠️
_____________
1 very long blink, lasting 4 seconds
Failed to mount USB drive. Ignoring.
  • Invalid filesystem
  • Corrupted partition table
  • Defective USB drive
  • Defective USB OTG adapter
  • Use a supported partition (FAT32, exFAT, NTFS, ext4)
  • Repair partition table
  • Try another USB drive
  • Try another USB OTG adapter
    • -⚠️ 3 long blinks, each lasting 1.5 seconds
    _____  _____  _____ +
    ⚠️
    _____  _____  _____
    3 long blinks, each lasting 1.5 seconds
    USB drive mounted successfully but femtofox-config.txt was not found. Ignoring. Config file missing. Create configuration file as described above. -⚠️ 5 long blinks, each lasting 1.5 seconds
    _____  _____  _____  _____  _____ +
    ⚠️
    _____  _____  _____  _____  _____
    5 long blinks, each lasting 1.5 seconds
    USB drive mounted successfully and femtofox-config.txt was found but did not contain readable configuration data. Ignoring. Configuration file improperly formatted or contains no data. Check configuration file contents as described above. -⚠️ 2 long blinks, each lasting 1 seconds, then 2 short blinks, each lasting 1/4 of a second. Repeats twice
    ___  ___  _  _  ___  ___  _  _ +
    ⚠️
    ___  ___  _  _  ___  ___  _  _
    2 long blinks, each lasting 1 seconds, then 2 short blinks, each lasting 1/4 of a second. Repeats twice
    Error while trying to implement a Meshtastic setting after 3 attempts. Some settings may have been implemented successfully.
  • The error may be transient.
  • Configuration file may contain improper data.
  • Try again.
  • Check configuration file contents as described above.
  • Check the log.

    This pattern may flash before other patterns. The pattern will repeat once for each failed setting.
    • -✅ 10 very fast blinks, each lasting 1/8th of a second
    . . . . . . . . . . +
    ✅
    . . . . . . . . . .
    10 very fast blinks, each lasting 1/8th of a second
    USB drive mounted successfully, and femtofox-config.txt was found and contained configuration data which was sent for deployment. Any affected services will now restart. You can disconnect the USB drive. This does not mean that the information in the config file is correct - only that it was readable.
    Note that the “success” boot code will flash if at least one setting is successfully read - even if the setting was not implemented successfully. -✅ 5 medium blinks, each lasting 0.5 seconds
    __  __  __  __  __ +
    ✅
    __  __  __  __  __
    5 medium blinks, each lasting 0.5 seconds
    Boot complete. Appears on every successful boot and always appears last.