mirror of
https://github.com/femtofox/femtofox.git
synced 2026-10-26 19:02:00 -04:00
fixed config.yaml corruption
This commit is contained in:
parent
2f48581f5b
commit
779d0f7eff
2 changed files with 184 additions and 184 deletions
|
|
@ -5,186 +5,186 @@
|
|||
### Uncomment the block that corresponds to your hardware
|
||||
### Including the "Module:" line!
|
||||
---
|
||||
Lora:
|
||||
|
||||
### Luckfox specific configs:
|
||||
|
||||
# Module: sx1262 # Waveshare SX126X XXXM
|
||||
# gpiochip: 1 # subtract 32 from the gpio numbers
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# CS: 16 #pin6 (GPIO pin 48 1C0)
|
||||
# IRQ: 23 #pin17 (GPIO pin 55 1C7)
|
||||
# Busy: 22 #pin16 (GPIO pin 54 1C6)
|
||||
# Reset: 25 #pin13 (GPIO pin 57 1D1)
|
||||
# spidev: spidev0.0
|
||||
# spiSpeed: 2000000
|
||||
|
||||
# Module: sx1262 # Bare E22-900M30S or similar
|
||||
# gpiochip: 1 # subtract 32 from the gpio numbers
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# DIO3_TCXO_VOLTAGE: true
|
||||
# CS: 16 #pin6 / GPIO48 1C0
|
||||
# IRQ: 23 #pin17 / GPIO55 1C7
|
||||
# Busy: 22 #pin16 / GPIO54 1C6
|
||||
# Reset: 25 #pin13 / GPIO57 1D1
|
||||
# RXen: 24 #pin12 / GPIO56 1D0
|
||||
# #TXen: bridge to DIO2 on E22 module
|
||||
# spidev: spidev0.0
|
||||
# spiSpeed: 2000000
|
||||
|
||||
### Luckfox end
|
||||
|
||||
# Module: sx1262 # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
|
||||
# CS: 7
|
||||
# IRQ: 17
|
||||
# Reset: 22
|
||||
|
||||
# Module: sx1262 # pinedio
|
||||
# CS: 0
|
||||
# IRQ: 10
|
||||
# Busy: 11
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# spidev: spidev0.1
|
||||
|
||||
# Module: RF95 # Adafruit RFM9x
|
||||
# Reset: 25
|
||||
# CS: 7
|
||||
# IRQ: 22
|
||||
# Busy: 23
|
||||
|
||||
# Module: RF95 # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html
|
||||
# Reset: 22
|
||||
# CS: 7
|
||||
# IRQ: 25
|
||||
|
||||
# Module: sx1280 # SX1280
|
||||
# CS: 21
|
||||
# IRQ: 16
|
||||
# Busy: 20
|
||||
# Reset: 18
|
||||
|
||||
# Module: sx1268 # SX1268-based modules, tested with Ebyte E22 400M33S
|
||||
# CS: 21
|
||||
# IRQ: 16
|
||||
# Busy: 20
|
||||
# Reset: 18
|
||||
# TXen: 6
|
||||
# RXen: 12
|
||||
# DIO3_TCXO_VOLTAGE: true
|
||||
|
||||
# DIO3_TCXO_VOLTAGE: true # the Waveshare Core1262 and others are known to need this setting
|
||||
|
||||
# TXen: x # TX and RX enable pins
|
||||
# RXen: x
|
||||
|
||||
# ch341_quirk: true # Uncomment this to use the chunked SPI transfer that seems to fix the ch341
|
||||
|
||||
# spiSpeed: 2000000
|
||||
|
||||
### Set gpio chip to use in /dev/. Defaults to 0.
|
||||
### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4
|
||||
# gpiochip: 4
|
||||
|
||||
### Specify the SPI device to use in /dev/. Defaults to spidev0.0
|
||||
### Some devices, like the pinedio, may require spidev0.1 as a workaround.
|
||||
# spidev: spidev0.0
|
||||
|
||||
### Define GPIO buttons here:
|
||||
|
||||
GPIO:
|
||||
# User: 6
|
||||
|
||||
### Define GPS
|
||||
|
||||
GPS:
|
||||
# SerialPath: /dev/ttyS0
|
||||
|
||||
### Specify I2C device, or leave blank for none
|
||||
|
||||
I2C:
|
||||
# I2CDevice: /dev/i2c-1
|
||||
|
||||
### Set up SPI displays here. Note that I2C displays are generally auto-detected.
|
||||
|
||||
Display:
|
||||
|
||||
### Waveshare 1.44inch LCD HAT
|
||||
# Panel: ST7735S
|
||||
# CS: 8 #Chip Select
|
||||
# DC: 25 # Data/Command pin
|
||||
# Backlight: 24
|
||||
# Width: 128
|
||||
# Height: 128
|
||||
# Reset: 27
|
||||
# OffsetX: 0
|
||||
# OffsetY: 0
|
||||
|
||||
### Adafruit PiTFT 2.8 TFT+Touchscreen
|
||||
# Panel: ILI9341
|
||||
# CS: 8
|
||||
# DC: 25
|
||||
# Width: 240
|
||||
# Height: 320
|
||||
# Rotate: true
|
||||
|
||||
### SHCHV 3.5 RPi TFT+Touchscreen
|
||||
# Panel: ILI9486
|
||||
# spidev: spidev0.0
|
||||
# BusFrequency: 30000000
|
||||
# DC: 24
|
||||
# Reset: 25
|
||||
# Width: 320
|
||||
# Height: 480
|
||||
# OffsetRotate: 2
|
||||
|
||||
### TZT 2.0 Inch TFT Display ST7789V 240RGBx320
|
||||
# Panel: ST7789
|
||||
# spidev: spidev0.0
|
||||
# # CS: 8 # can be freely chosen
|
||||
# BusFrequency: 80000000
|
||||
# DC: 24 # can be freely chosen
|
||||
# Width: 320
|
||||
# Height: 240
|
||||
# Reset: 25 # can be freely chosen
|
||||
# Rotate: true
|
||||
# OffsetRotate: 1
|
||||
# Invert: true
|
||||
|
||||
### You can also specify the spi device for the display to use
|
||||
# spidev: spidev0.0
|
||||
|
||||
Touchscreen:
|
||||
### Note, at least for now, the touchscreen must have a CS pin defined, even if you let Linux manage the CS switching.
|
||||
|
||||
# Module: STMPE610 # Option 1 for Adafruit PiTFT 2.8
|
||||
# CS: 7
|
||||
# IRQ: 24
|
||||
|
||||
# Module: FT5x06 # Option 2 for Adafruit PiTFT 2.8
|
||||
# IRQ: 24
|
||||
# I2CAddr: 0x38
|
||||
|
||||
### You can also specify the spi device for the touchscreen to use
|
||||
# spidev: spidev0.0
|
||||
|
||||
|
||||
Input:
|
||||
### Configure device for direct keyboard input
|
||||
|
||||
# KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd
|
||||
|
||||
###
|
||||
|
||||
Logging:
|
||||
LogLevel: debug # debug, info, warn, error
|
||||
TraceFile: /var/log/meshtasticd.json
|
||||
AsciiLogs: true # default if not specified is !isatty() on stdout
|
||||
|
||||
Webserver:
|
||||
Port: 443 # Port for Webserver & Webservices
|
||||
RootPath: /usr/share/doc/meshtasticd/web # Root Dir of WebServer
|
||||
|
||||
General:
|
||||
MaxNodes: 200
|
||||
MaxMessageQueue: 100
|
||||
ConfigDirectory: /etc/meshtasticd/config.d/
|
||||
Lora:
|
||||
|
||||
### Luckfox specific configs:
|
||||
|
||||
# Module: sx1262 # Waveshare SX126X XXXM
|
||||
# gpiochip: 1 # subtract 32 from the gpio numbers
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# CS: 16 #pin6 (GPIO pin 48 1C0)
|
||||
# IRQ: 23 #pin17 (GPIO pin 55 1C7)
|
||||
# Busy: 22 #pin16 (GPIO pin 54 1C6)
|
||||
# Reset: 25 #pin13 (GPIO pin 57 1D1)
|
||||
# spidev: spidev0.0
|
||||
# spiSpeed: 2000000
|
||||
|
||||
# Module: sx1262 # Bare E22-900M30S or similar
|
||||
# gpiochip: 1 # subtract 32 from the gpio numbers
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# DIO3_TCXO_VOLTAGE: true
|
||||
# CS: 16 #pin6 / GPIO48 1C0
|
||||
# IRQ: 23 #pin17 / GPIO55 1C7
|
||||
# Busy: 22 #pin16 / GPIO54 1C6
|
||||
# Reset: 25 #pin13 / GPIO57 1D1
|
||||
# RXen: 24 #pin12 / GPIO56 1D0
|
||||
# #TXen: bridge to DIO2 on E22 module
|
||||
# spidev: spidev0.0
|
||||
# spiSpeed: 2000000
|
||||
|
||||
### Luckfox end
|
||||
|
||||
# Module: sx1262 # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
|
||||
# CS: 7
|
||||
# IRQ: 17
|
||||
# Reset: 22
|
||||
|
||||
# Module: sx1262 # pinedio
|
||||
# CS: 0
|
||||
# IRQ: 10
|
||||
# Busy: 11
|
||||
# DIO2_AS_RF_SWITCH: true
|
||||
# spidev: spidev0.1
|
||||
|
||||
# Module: RF95 # Adafruit RFM9x
|
||||
# Reset: 25
|
||||
# CS: 7
|
||||
# IRQ: 22
|
||||
# Busy: 23
|
||||
|
||||
# Module: RF95 # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html
|
||||
# Reset: 22
|
||||
# CS: 7
|
||||
# IRQ: 25
|
||||
|
||||
# Module: sx1280 # SX1280
|
||||
# CS: 21
|
||||
# IRQ: 16
|
||||
# Busy: 20
|
||||
# Reset: 18
|
||||
|
||||
# Module: sx1268 # SX1268-based modules, tested with Ebyte E22 400M33S
|
||||
# CS: 21
|
||||
# IRQ: 16
|
||||
# Busy: 20
|
||||
# Reset: 18
|
||||
# TXen: 6
|
||||
# RXen: 12
|
||||
# DIO3_TCXO_VOLTAGE: true
|
||||
|
||||
# DIO3_TCXO_VOLTAGE: true # the Waveshare Core1262 and others are known to need this setting
|
||||
|
||||
# TXen: x # TX and RX enable pins
|
||||
# RXen: x
|
||||
|
||||
# ch341_quirk: true # Uncomment this to use the chunked SPI transfer that seems to fix the ch341
|
||||
|
||||
# spiSpeed: 2000000
|
||||
|
||||
### Set gpio chip to use in /dev/. Defaults to 0.
|
||||
### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4
|
||||
# gpiochip: 4
|
||||
|
||||
### Specify the SPI device to use in /dev/. Defaults to spidev0.0
|
||||
### Some devices, like the pinedio, may require spidev0.1 as a workaround.
|
||||
# spidev: spidev0.0
|
||||
|
||||
### Define GPIO buttons here:
|
||||
|
||||
GPIO:
|
||||
# User: 6
|
||||
|
||||
### Define GPS
|
||||
|
||||
GPS:
|
||||
# SerialPath: /dev/ttyS0
|
||||
|
||||
### Specify I2C device, or leave blank for none
|
||||
|
||||
I2C:
|
||||
# I2CDevice: /dev/i2c-1
|
||||
|
||||
### Set up SPI displays here. Note that I2C displays are generally auto-detected.
|
||||
|
||||
Display:
|
||||
|
||||
### Waveshare 1.44inch LCD HAT
|
||||
# Panel: ST7735S
|
||||
# CS: 8 #Chip Select
|
||||
# DC: 25 # Data/Command pin
|
||||
# Backlight: 24
|
||||
# Width: 128
|
||||
# Height: 128
|
||||
# Reset: 27
|
||||
# OffsetX: 0
|
||||
# OffsetY: 0
|
||||
|
||||
### Adafruit PiTFT 2.8 TFT+Touchscreen
|
||||
# Panel: ILI9341
|
||||
# CS: 8
|
||||
# DC: 25
|
||||
# Width: 240
|
||||
# Height: 320
|
||||
# Rotate: true
|
||||
|
||||
### SHCHV 3.5 RPi TFT+Touchscreen
|
||||
# Panel: ILI9486
|
||||
# spidev: spidev0.0
|
||||
# BusFrequency: 30000000
|
||||
# DC: 24
|
||||
# Reset: 25
|
||||
# Width: 320
|
||||
# Height: 480
|
||||
# OffsetRotate: 2
|
||||
|
||||
### TZT 2.0 Inch TFT Display ST7789V 240RGBx320
|
||||
# Panel: ST7789
|
||||
# spidev: spidev0.0
|
||||
# # CS: 8 # can be freely chosen
|
||||
# BusFrequency: 80000000
|
||||
# DC: 24 # can be freely chosen
|
||||
# Width: 320
|
||||
# Height: 240
|
||||
# Reset: 25 # can be freely chosen
|
||||
# Rotate: true
|
||||
# OffsetRotate: 1
|
||||
# Invert: true
|
||||
|
||||
### You can also specify the spi device for the display to use
|
||||
# spidev: spidev0.0
|
||||
|
||||
Touchscreen:
|
||||
### Note, at least for now, the touchscreen must have a CS pin defined, even if you let Linux manage the CS switching.
|
||||
|
||||
# Module: STMPE610 # Option 1 for Adafruit PiTFT 2.8
|
||||
# CS: 7
|
||||
# IRQ: 24
|
||||
|
||||
# Module: FT5x06 # Option 2 for Adafruit PiTFT 2.8
|
||||
# IRQ: 24
|
||||
# I2CAddr: 0x38
|
||||
|
||||
### You can also specify the spi device for the touchscreen to use
|
||||
# spidev: spidev0.0
|
||||
|
||||
|
||||
Input:
|
||||
### Configure device for direct keyboard input
|
||||
|
||||
# KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd
|
||||
|
||||
###
|
||||
|
||||
Logging:
|
||||
LogLevel: debug # debug, info, warn, error
|
||||
TraceFile: /var/log/meshtasticd.json
|
||||
AsciiLogs: true # default if not specified is !isatty() on stdout
|
||||
|
||||
Webserver:
|
||||
Port: 443 # Port for Webserver & Webservices
|
||||
RootPath: /usr/share/doc/meshtasticd/web # Root Dir of WebServer
|
||||
|
||||
General:
|
||||
MaxNodes: 200
|
||||
MaxMessageQueue: 100
|
||||
ConfigDirectory: /etc/meshtasticd/config.d/
|
||||
|
|
@ -5,7 +5,7 @@ echo -n "Enter wifi password: "
|
|||
stty -echo # Disable terminal echo
|
||||
read PASSWORD
|
||||
stty echo # Re-enable terminal echo
|
||||
echo "[1;32m*** SSID saved. Wifi requires adapter ***\e[0m\n"
|
||||
echo "\n[1;32m*** SSID saved. Wifi requires adapter ***\e[0m\n"
|
||||
|
||||
|
||||
sudo mount -t tmpfs tmpfs /run -o remount,size=32M,nosuid,noexec,relatime,mode=755 #Embiggen tmpfs - prevents problems.
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue