From 77c06efa09a6fd04803b2a970b79104669f234bf Mon Sep 17 00:00:00 2001 From: nagumii Date: Fri, 15 Nov 2024 16:32:50 +0200 Subject: [PATCH] Create config.yaml --- meshtasticd/config.yaml | 190 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 190 insertions(+) create mode 100644 meshtasticd/config.yaml diff --git a/meshtasticd/config.yaml b/meshtasticd/config.yaml new file mode 100644 index 0000000..970a4bf --- /dev/null +++ b/meshtasticd/config.yaml @@ -0,0 +1,190 @@ +### Many device configs have been moved to /etc/meshtasticd/available.d +### To activate, simply copy or link the appropriate file into /etc/meshtasticd/config.d + +### Define your devices here using Broadcom pin numbering +### Uncomment the block that corresponds to your hardware +### Including the "Module:" line! +--- +Lora: + +### Luckfox + + Module: sx1262 # Waveshare SX126X XXXM + gpiochip: 1 # subtract 32 from the gpio numbers + DIO2_AS_RF_SWITCH: true + CS: 16 #pin6 (GPIO pin 48 1C0) + IRQ: 23 #pin17 (GPIO pin 55 1C7) + Busy: 22 #pin16 (GPIO pin 54 1C6) + Reset: 25 #pin13 (GPIO pin 57 1D1) + spidev: spidev0.0 + spiSpeed: 2000000 + +# Module: sx1262 # Bare E22-900M30S or similar +# gpiochip: 1 # subtract 32 from the gpio numbers +# DIO2_AS_RF_SWITCH: true +# CS: 16 #pin6 / GPIO48 1C0 +# IRQ: 23 #pin17 / GPIO55 1C7 +# Busy: 22 #pin16 / GPIO54 1C6 +# Reset: 25 #pin13 / GPIO57 1D1 +# RXen: 24 #pin12 / GPIO56 1D0 +# #TXen: bridge to DIO2 on E22 module +# spidev: spidev0.0 +# spiSpeed: 2000000 + + +### Luckfox end + +# Module: sx1262 # Waveshare SX1302 LISTEN ONLY AT THIS TIME! +# CS: 7 +# IRQ: 17 +# Reset: 22 + +# Module: sx1262 # pinedio +# CS: 0 +# IRQ: 10 +# Busy: 11 +# DIO2_AS_RF_SWITCH: true +# spidev: spidev0.1 + +# Module: RF95 # Adafruit RFM9x +# Reset: 25 +# CS: 7 +# IRQ: 22 +# Busy: 23 + +# Module: RF95 # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html +# Reset: 22 +# CS: 7 +# IRQ: 25 + +# Module: sx1280 # SX1280 +# CS: 21 +# IRQ: 16 +# Busy: 20 +# Reset: 18 + +# Module: sx1268 # SX1268-based modules, tested with Ebyte E22 400M33S +# CS: 21 +# IRQ: 16 +# Busy: 20 +# Reset: 18 +# TXen: 6 +# RXen: 12 +# DIO3_TCXO_VOLTAGE: true + +# DIO3_TCXO_VOLTAGE: true # the Waveshare Core1262 and others are known to need this setting + +# TXen: x # TX and RX enable pins +# RXen: x + +# ch341_quirk: true # Uncomment this to use the chunked SPI transfer that seems to fix the ch341 + +# spiSpeed: 2000000 + +### Set gpio chip to use in /dev/. Defaults to 0. +### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4 +# gpiochip: 4 + +### Specify the SPI device to use in /dev/. Defaults to spidev0.0 +### Some devices, like the pinedio, may require spidev0.1 as a workaround. +# spidev: spidev0.0 + +### Define GPIO buttons here: + +GPIO: +# User: 6 + +### Define GPS + +GPS: +# SerialPath: /dev/ttyS0 + +### Specify I2C device, or leave blank for none + +I2C: +# I2CDevice: /dev/i2c-1 + +### Set up SPI displays here. Note that I2C displays are generally auto-detected. + +Display: + +### Waveshare 1.44inch LCD HAT +# Panel: ST7735S +# CS: 8 #Chip Select +# DC: 25 # Data/Command pin +# Backlight: 24 +# Width: 128 +# Height: 128 +# Reset: 27 +# OffsetX: 0 +# OffsetY: 0 + +### Adafruit PiTFT 2.8 TFT+Touchscreen +# Panel: ILI9341 +# CS: 8 +# DC: 25 +# Width: 240 +# Height: 320 +# Rotate: true + +### SHCHV 3.5 RPi TFT+Touchscreen +# Panel: ILI9486 +# spidev: spidev0.0 +# BusFrequency: 30000000 +# DC: 24 +# Reset: 25 +# Width: 320 +# Height: 480 +# OffsetRotate: 2 + +### TZT 2.0 Inch TFT Display ST7789V 240RGBx320 +# Panel: ST7789 +# spidev: spidev0.0 +# # CS: 8 # can be freely chosen +# BusFrequency: 80000000 +# DC: 24 # can be freely chosen +# Width: 320 +# Height: 240 +# Reset: 25 # can be freely chosen +# Rotate: true +# OffsetRotate: 1 +# Invert: true + +### You can also specify the spi device for the display to use +# spidev: spidev0.0 + +Touchscreen: +### Note, at least for now, the touchscreen must have a CS pin defined, even if you let Linux manage the CS switching. + +# Module: STMPE610 # Option 1 for Adafruit PiTFT 2.8 +# CS: 7 +# IRQ: 24 + +# Module: FT5x06 # Option 2 for Adafruit PiTFT 2.8 +# IRQ: 24 +# I2CAddr: 0x38 + +### You can also specify the spi device for the touchscreen to use +# spidev: spidev0.0 + + +Input: +### Configure device for direct keyboard input + +# KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd + +### + +Logging: + LogLevel: debug # debug, info, warn, error + TraceFile: /var/log/meshtasticd.json + AsciiLogs: true # default if not specified is !isatty() on stdout + +Webserver: + Port: 443 # Port for Webserver & Webservices + RootPath: /usr/share/doc/meshtasticd/web # Root Dir of WebServer + +General: + MaxNodes: 200 + MaxMessageQueue: 100 + ConfigDirectory: /etc/meshtasticd/config.d/