+
The Luckfox Pico Mini is a compact and power efficient (~0.25w) Linux capable board, ideal for running TC2 Meshtastic BBS (or anything else).
Advantages:
- Tiny size (~28x21mm)
- Power efficiency (~0.25w)
-- Full Linux (Ubuntu!)
+- Full Linux CLI (Ubuntu, Buildroot, Alpine)
- USB host support
- Cheap - $7-8 on Waveshare (also available on Amazon)! Get the A model - the B just has added flash storage that’s too small for our purposes.
@@ -18,12 +39,13 @@
By default, no simple way to get online (no built in wifi/BLE/ethernet). Ethernet can be easily added - wifi still work in progress - see Networking below)
Annoying SDK for building firmware images
No simple way to compile drivers (no available Linux headers - if anyone manages to compile the headers, please let me know)
+
USB seems very power limited - highest observed current is low - just 0.08a at 5v (0.4w). It seems that if power draw exceeds this limit, the device will bootloop or hard crash.
Issues / to do:
-- WIFI over USB (accomplished, optimizing)
+- WIFI over USB or UART (accomplished, unstable, optimizing)
- Meshtasticd to run LoRa radio over SPI (accomplished, details to follow)
-- Test RAK19003 via UART
+
Project goals:
@@ -41,7 +63,7 @@
- Drivers for real time clock over i2c - tested working with DS3231 with DS1307 driver (should be compatible with DS1307, DS1337 and DS3231).
See supported hardware below.
-
Also, I turned off the activity LED. Every μW counts!
+
Also, I turned off the activity LED - every μW counts!
I’ve built three Ubuntu 22.04.5 LTS images with Luckfox’s SDK:
- A ‘fresh’ image with no changes but with the added drivers for usb ethernet, wifi, serial, RTC and mass storage.
@@ -90,34 +112,40 @@
| Meshtastic nodes |
-RAK4631 with RAK19007 base board |
-RAK19003 |
-RAK4630 and 4631 are the same |
+RAK4631 with RAK19007 or RAK19003 base boards |
+ |
+RAK4630 and 4631 are the same. |
+
+
+| USB wifi adapter chipsets |
+RTL8188EUS, MT7601U |
+ |
+USB power limitations are causing many issues. Unreliable - work in progress. |
| Misc. hardware |
USB hubs, thumb drives, SD card readers |
|
-Highest observed current is low - just 0.05a at 5v (0.28w). It seems that if power draw exceeds this limit, the device will bootloop. |
+Highest observed current is low - just 0.08a at 5v (0.4w). It seems that if power draw exceeds this limit, the device will bootloop or hard crash. |
-Installation
+Installation - connection to Meshtastic node via UART or USB
Choosing a MicroSD card: Any reasonably fast MicroSD card of 32gb or higher should work, but ideally use a card that supports UHS-1 or higher, and is rated for high endurance.
- Uncompress the 7z file - will require ~29gb of space. In windows, use 7-zip.
- Flash the image your MicroSD card using Balena Etcher or your favorite flashing program. You will likely get a warning that the image appears to be invalid or has no partition table. This is normal.
- Insert the microSD card into the Pico Mini.
- Connect Pico Mini to Meshtastic radio via pins or USB, depending on image flashed. If using pins - use pins 10 and 11 on the Luckfox board.
-- For the rak19007 (with the rak4631 daughter board):
+- For the rak19007 or rak19003 (with the rak4631/rak4630 daughter board):
-- In Position settings, set
GPS: NOT_PRESENT
+- In Position settings, set
GPS: NOT_PRESENT. The Rak does not support GPS and UART simultaneously at this time.
- If using UART comms, Serial Module settings:
Serial: Enabled
Echo: off
-RX: 15
-TX: 16
+RX: 15 (rak19007 and rak19003 with TX1/RX1), 19 (rak19003 with TX0/RX0)`
+TX: 16 (rak19007 and rak19003 with TX1/RX1), 20 (rak19003 with TX0/RX0)`
Serial baud rate: 115200
Timeout: 0
Serial mode: PROTO
@@ -138,3 +166,8 @@


+