* Add a Solar calculator with offline NASA POWER data Estimates a solar array's typical-year production from a location and the panels; everything else has defaults under an optional "Fine-tune" section. The model works from 12 monthly averages: Klein's average day per month, the Erbs monthly diffuse fraction, Collares-Pereira & Rabl / Liu & Jordan hourly split, HDKR transposition for fixed, single-axis and dual-axis arrays, then PVWatts' ASHRAE incidence loss, SAPM cell temperature, DC power, system losses and optional inverter. "Best for the year" and "Best for winter" sweep the tilt. Sunlight, diffuse, albedo and temperature come from NASA POWER's 2001-2020 climatology on a 1 degree grid, packed into app/public/data (3.1 MB, ~1 MB gzipped) by scripts/build_solar_climatology.py and fetched only when the calculator opens. Users can replace it with their own monthly values. Every setting lives in the URL, with defaults left out, so the Share button shares the whole configuration. Against PVWatts v8 for a 1 kW fixed array: Phoenix +0.6%, Seattle +8.8%, Anchorage +8.0% annually; these are recorded as tests. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Open the Solar calculator from the map, pins and current location The map's right-click (or long-press) menu gains "Calculate Solar Performance", and each saved pin a sun button; both open the calculator at that location. A button beside Latitude fills in the browser's current location. Locations are rounded to 4 decimals, and longitudes from a map panned around the world are wrapped back to -180..180. The map removed lat/lon/z from the URL when it closed, even after navigating to another page, which stripped the calculator's location from its URL (and from links shared with the Share button). It now only cleans up while the URL is still a map page. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Add off-grid sizing to the Solar calculator A new "Off-grid sizing" tab sizes a battery system for the darkest month from a list of devices (watts x hours per day): - Battery bank for a number of days without sun, for LiFePO4 or lead-acid, at 12, 24 or 48 V. Outdoor lead-acid is enlarged for the cold; outdoor lithium warns against charging below 0 C. - Panels needed, from the worst month's DC production per kW at the chosen angle, with a button to apply the count. A PWM controller's loss (battery voltage over the panel's Vmp) raises the count. - Charge controller current, and the string voltage on the coldest morning against the controller's limit, since cold panels exceed their rated Voc. The coldest morning defaults to 25 C below the coldest monthly average. All inputs live in the URL like the rest of the calculator. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Bump wrolpi-help for the Solar calculator help page Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Credit NASA POWER as it asks, and say how the data was changed - The calculator gains a "Data attribution" link under the location with NASA POWER's requested acknowledgment, the data reference (Climatology API v2.10.0, downloaded 2026/10/04), the CC BY 4.0 license, and how WROLPi modified the data (rounded to one byte per value, temperature averaged into 1 degree cells, interpolated between cells), which CC BY 4.0 requires. - The build script writes the same text to solar-climatology.LICENSE.txt beside the data, with the API version taken from NASA's responses and the date the tiles were downloaded. A test keeps the page and file in step. - Bumps wrolpi-help for the updated attribution in the help page. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Solar: fix PWM sizing, Voc sign, unit switching and loading on review - PWM usable power now uses the string's voltage (Vmp x panels in series), delivers nothing when the charging voltage is at or above the string's Voc, and falls off between Vmp and Voc. The "too little voltage" warning covers PWM as well as MPPT. Previously two panels in series counted double, and a panel that could not charge a 48 V bank counted as fully usable. - A Voc temperature coefficient entered without its minus sign is treated as negative, in the math, the URL and the input, so the cold-morning check cannot be made too generous. - Switching Fahrenheit on or off converts the entered temperatures instead of reinterpreting them. - While the sunlight data downloads, the off-grid tab shows a loader rather than asking for a location, and holds the cold-morning verdict until the site's temperatures are known or one has been entered. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Solar: move the data attribution to the bottom of the page The full NASA POWER acknowledgment, license and changes now sit in a small "Data attribution" section at the end of the calculator, always visible, instead of behind a link under the location. The source line under the location points to it. Bumps wrolpi-help to match. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Solar: drop the data source line under the location The attribution at the bottom of the page is enough. The line under the location now only appears to report the data's state: loading, failed to load, or replaced by the user's own values. Bumps wrolpi-help for the refreshed screenshot. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> --------- Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com> |
||
|---|---|---|
| .. | ||
| cypress | ||
| public | ||
| scripts | ||
| src | ||
| .gitignore | ||
| cypress.config.js | ||
| package-lock.json | ||
| package.json | ||
| README.md | ||
| serve.json | ||
| tsconfig.json | ||
Getting Started with Create React App
This project was bootstrapped with Create React App.
Available Scripts
In the project directory, you can run:
npm start
Runs the app in the development mode.
Open http://localhost:3000 to view it in your browser.
The page will reload when you make changes.
You may also see any lint errors in the console.
npm test
Launches the test runner in the interactive watch mode.
See the section about running tests for more
information.
npm run build
Builds the app for production to the build folder.
It correctly bundles React in production mode and optimizes the build for the best performance.
The build is minified and the filenames include the hashes.
Your app is ready to be deployed!
See the section about deployment for more information.
npm run eject
Note: this is a one-way operation. Once you eject, you can't go back!
If you aren't satisfied with the build tool and configuration choices, you can eject at any time. This command will
remove the single build dependency from your project.
Instead, it will copy all the configuration files and the transitive dependencies (webpack, Babel, ESLint, etc) right
into your project so you have full control over them. All of the commands except eject will still work, but they will
point to the copied scripts so you can tweak them. At this point you're on your own.
You don't have to ever use eject. The curated feature set is suitable for small and middle deployments, and you
shouldn't feel obligated to use this feature. However we understand that this tool wouldn't be useful if you couldn't
customize it when you are ready for it.
Learn More
You can learn more in the Create React App documentation.
To learn React, check out the React documentation.
Code Splitting
This section has moved here: https://facebook.github.io/create-react-app/docs/code-splitting
Analyzing the Bundle Size
This section has moved here: https://facebook.github.io/create-react-app/docs/analyzing-the-bundle-size
Making a Progressive Web App
This section has moved here: https://facebook.github.io/create-react-app/docs/making-a-progressive-web-app
Advanced Configuration
This section has moved here: https://facebook.github.io/create-react-app/docs/advanced-configuration
Deployment
This section has moved here: https://facebook.github.io/create-react-app/docs/deployment
npm run build fails to minify
This section has moved here: https://facebook.github.io/create-react-app/docs/troubleshooting#npm-run-build-fails-to-minify